VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 110 / 317

INJECTOR

Function

Provide the correct amount of fuel at the correct

time.

Operation / Operating principle

Injector coil is excited for the petrol passage to

open.

Pinout:

1. Power from relay

2. Ground from control unit

ELECTRICAL ERRORS

Injector P0201

- shorted to positive / shorted to negative / open circuit.

Error cause

Shorted to positive: excessive voltage to PIN 34 of the control unit connector.

Shorted to negative: zero voltage to the PIN 1 of the injector connector.

Open circuit: circuit interruption.

Troubleshooting

Shorted to positive:

- Disconnect the injector connector, turn ignition switch to ON and activate the component using the

diagnostic tool.

- Verify the absence of voltage at the injector connector PIN 2; if present restore the cable harness,

otherwise proceed with the following checks.

Shorted to negative:

- Disconnect the injector connector, turn ignition switch to ON and activate the component using the

diagnostic tool.

- Verify the presence of voltage at the ends of the injector connector; if there is no voltage, restore the

cable harness, otherwise proceed with the following checks.

Open circuit:

- Perform the check of the injector and control unit connectors.

- Verify continuity of the cable harness between the control unit connector and the injector connector

(control unit PIN 34 - injector PIN 2). If there is no continuity, restore the cable harness.

FUEL PUMP

ELECTRICAL ERRORS

Fuel pump relay P0230

- shorted to positive / shorted to negative / open circuit.

Error cause

Shorted to positive: excessive voltage at PIN 22 of the control unit connector.

Short circuit to negative: null voltage at PIN 86 of the injection relay.

Electrical system

Vespa GTS Super 300 ie (2008)

ELE SYS - 110

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands