Tyco Fire & Security CWSI CP-3600 Operating And Installation Instruction Manual Download Page 74

Page: 74 / 81

P/N CWSI-IM-C3K6 Rev. F

© 2017 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision
date and are subject to change without notice.

CP-3600(+) to SIA translation table

CP-3600(+) EVENT

SIA CODE

DESCRIPTION

Alarm A

Fire Alarm

Alarm A Reset

Fire Alarm Restore

Alarm B

Fire Alarm

Alarm B Reset

Fire Alarm Restore

Alarm C

Fire Alarm

Alarm C Reset

Fire Alarm Restore

Alarm C Supervisory

Fire Supervisory

Alarm

C Supervisory

Reset

Fire Supervisory

Restore

All Troubles except A/C

loss and Supervisory

Trouble

FT Fire

Trouble

All Trouble Resets

except A/C loss and

Supervisory

Fire Trouble Restore

Supervisory Trouble

Fire Supervisory

Trouble

Supervisory Trouble

Reset

Fire Supervisory

Trouble Restore

A/C Loss Trouble

AC Trouble

A/C Loss Restore

AC Restoral

Panel Test

Start Test

Panel Test Reset

Test End

Table 4

Summary of Contents for CWSI CP-3600


















































































Search results

Summary of Contents for CWSI CP-3600

Reviews:

Tyco Fire & Security CWSI CP-3600, Operating And Installation Instruction Manual, Page: 74 / 81

Search results

Summary of Contents for CWSI CP-3600

Reviews: