Tyco Fire & Security CWSI CP-3600 Operating And Installation Instruction Manual Download Page 24 | Manualshive

Page: 24 / 81

Tyco Fire & Security CWSI CP-3600 Operating And Installation Instruction Manual Download Page 24

P/N CWSI-IM-C3K6 Rev. F

© 2017 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision
date and are subject to change without notice.

24

4.2.3 Menu Access, Navigation, Data Entry and Field Editing

When any of the soft key buttons are pressed to gain menu access you will be prompted to enter a
password. The password entry screen is shown below.

Password Entry

The cursor will be blinking in the password entry field under the first character to be entered. Use the
UP/DOWN keys to select the first number in the code. There are ten choices 0-9.

The default

password is 3000

so the first character is 3. After the number 3 is showing in the first digit, press the

RIGHT key to move the cursor to the next position then UP/DOWN to select the second character and
so on until all four numbers are showing. Press the ENTER key when the correct password is showing
and you will have access to the menus. If ENTER is pressed with any of the wrong characters showing
or 4 numbers are not entered, the field will clear and the entire password will have to be entered again.
When a correct password is entered a ten minute timer will start allowing menu access without
reentering the password. You will only have to enter the password again if ten minutes elapses without
any programming menu activity.

Once the correct password is entered the menu choices are displayed. Use the UP/DOWN keys to
move the highlighted box. When the desired menu is highlighted press the ENTER key and that menu
choice will be selected. Pressing the BACK key will take you one menu level back.

When you have accessed a programming screen that has data fields which can be edited, a blinking
cursor will be present under the first field. Press the ENTER key to edit the field or use the UP/DOWN
keys to move the cursor so it is under the field you want to edit then press the ENTER key. The field
being edited will be highlighted.

0 6 : 2 7 P M

1 1 / 2 2 / 2 0 0 7

C o n f i g

P r o g r a m

L o g s I n f o

E n t e r P a s s w o r d :

«
...
22
23
24
25
26
...
»

Summary of Contents for CWSI CP-3600


















































































Reviews:

No comments