Toshiba TLCS-900/H1 Series Manual Download Page 332 | Manualshive

Page: 332 / 652

background image

TMP92CF30

2009-06-12

92CF30-330

3.15.6 Data Transfer in I

2

C Bus Mode

(1)

Device initialization

Set the SBICR1<ACK, SCK2:0>, Set SBIBR1 to “1” and clear bits 7 to 5 and 3 in the

SBICR1 to “0”.
Set a slave address <SA6:0> and the <ALS> (<ALS>

=

“0” when an addressing format)

to the I2CAR.
For specifying the default setting to a slave receiver mode, clear “0” to the <MST, TRX,
BB> and set “1” to the <PIN>, “10” to the <SBIM1:0>.

7 6 5 4 3 2 1 0

SBICR1

←

0 0 0 X 0 X X X

Set acknowledge and SCL clock.

I2CAR

←

X X X X X X X X

Set slave address and address recognition mode.

SBICR2

←

0 0 0 1 1 0 0 0

Set to slave receiver mode.

Note: X: Don’t care

(2)

Start condition and slave address generation

a.

Master Mode

In the Master Mode, the start condition and the slave address are generated as

follows.
Check a bus free status (when <BB>

=

“0”).

Set the SBICR1<ACK> to “1” (Acknowledge Mode) and specify a slave address
and a direction bit to be transmitted to the SBIDBR.
When SBICR2<BB>

=

“0”, the start condition are generated by writing “1111” to

SBICR2<MST, TRX, BB, PIN>. Subsequently to the start condition, nine clocks
are output from the SCL pin. While eight clocks are output, the slave address and
the direction bit which are set to the SBIDBR. At the 9th clock, the SDA line is
released and the acknowledge signal is received from the slave device.
An INTSBI interrupt request occurs at the falling edge of the 9th clock. The
<PIN> is cleared to “0”. In the Master Mode, the SCL pin is pulled down to the
Low-level while <PIN> is “0”. When an interrupt request occurs, the <TRX> is
changed according to the direction bit only when an acknowledge signal is
returned from the slave device.

Setting in main routine

7 6 5 4 3 2 1 0

Reg.

←

SBISR

Reg.

←

Reg. e 0x20

if Reg.

≠

0x00

Wait until bus is free.

Then

SBICR1

←

X X X 1 X X X X

Set to acknowledgement mode.

SBIDBR1

←

X X X X X X X X

Set slave address and direction bit.

SBICR2

←

1 1 1 1 1 0 0 0

Generate start condition.

In INTSBI interrupt routine

INTCLR

←

0X2a

Clear the interrupt request

Process

End of interrupt

«
...
330
331
332
333
334
...
»

Summary of Contents for TLCS-900/H1 Series













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TLCS-900/H1 Series

Brand: CAME Pages: 19

Brand: Laird Pages: 36

Brand: Delta Electronics Pages: 1

Parallel Printer Card PIOC

Brand: B&B Electronics Pages: 16

Brand: Telit Wireless Solutions Pages: 113

Marconi OMS 1200

Brand: Ericsson Pages: 136

Brand: Teletronics International Pages: 57

NVR41-4KS2 Series

Brand: Dahua Pages: 452

Brand: MA lighting Pages: 49

LEDWALL Optimizer HQ P2

Brand: Gundermann VIDEOWALL Pages: 12

Brand: IBM Pages: 130

Brand: ZyXEL Communications Pages: 2

Brand: Cypress Semiconductor Pages: 26

Brand: RAID Pages: 80

Brand: Uctronics Pages: 12

Brand: Lanner Pages: 99

Brand: Freescale Semiconductor Pages: 42

Diamond Systems DS-MPE-CAN2L

Brand: Fortec Star Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands