Toshiba e-STUDIO350 Service Manual Download Page 79

Page: 79 / 286

November 2003 © TOSHIBA TEC

4 - 1

e-STUDIO350/450 GENERAL OPERATION

GENERAL OPERATION

4.1

Overview of Operation

Operation of equipment

Operation during initializing, pre-running and ready

Drawer feed copying by [START] button

Copying operation

Bypass feed copying

Interrupt copying

4.2 Description of Operation

4.2.1 Warming-up

(1)

Initialization

•

Power ON

•

IH coil ON

•

Set number “1” reproduction ratio “100%” and “WAIT WARMING UP” are displayed

•

Fan motors ON

•

Initialization of scanning system

– The carriage moves to the home position.

– The carriage moves to the peak detection position.

– The exposure lamp is turned ON.

– Peak detection (white color is detected by the shading correction plate)

– The exposure lamp is turned OFF.

•

“READY (WARMING UP)” is displayed

(2)

Pre-running operation

The pre-running operation is started when the temperature of the fuser roller surface reaches a

certain temperature.

•

Fuser roller rotated

•

Drum rotated

– The main motor is turned ON.

•

Initialization of feeding system

– Each drawer tray goes up.

•

Pre-running operation stops after five seconds.

(3)

When the surface temperature of the fuser roller becomes sufficient for fusing,

•

“READY” is displayed.

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 79 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: