Toshiba e-STUDIO350 Service Manual Download Page 110

Page: 110 / 286

e-STUDIO350/450 SCANNER

6 - 2

November 2003 © TOSHIBA TEC

6.2

Construction

a. Exposure lamp

This lamp is the light source to irradiate the original on the glass. (One 16W xenon lamp)

b. Lamp inverter

Controls lighting of the xenon lamp.

c. Reflector

This is a plate to efficiently direct the light from the exposure lamp to the surface of the original on

the glass.

d. Mirror-1

This mirror directs the light reflected from the original to the mirror-2 described later.

Fig. 6-202

Fig. 6-201

The following shows the construction and purpose of the scanning system:

(1)

Original glass

This is a glass on which original is placed. The light from the exposure lamp is irradiated to the

original through this glass.

(2)

Carriage-1

Carriage-1 consists of the exposure lamp, lamp inverters, reflector, mirror-1, etc. It is driven by the

scan motor and scans an original on the glass.

Reflector

Lamp inverter

Exposure lamp

Mirror-1

Original glass

Original

Exposure lamp

Lamp inverter

Reflector

Mirror-1

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 110 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: