Toshiba e-STUDIO350 Service Manual Download Page 169

Page: 169 / 286

November 2003 © TOSHIBA TEC

9 - 19

e-STUDIO350/450 PAPER FEEDING SYSTEM

Fig. 9-439

Fig. 9-438

Fig. 9-437

Fig. 9-436

(11) Take off the jam access cover.

(12) Disconnect the connector and remove the har-

ness.

(13) Remove 2 screws and take off the right trans-

port guide.

Note:

When taking off the right transport guide, be

careful not to come off the bypass transport

guide and the spring together with it.

(14) Release the latch and take off the lower

drawer feed sensor.

Jam access cover

Harness

Connector

Bypass transport guide

Spring

Screw

Right transport guide

Right transport
guide

Lower drawer feed
sensor

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 169 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: