manualshive.com logo in svg

Toshiba e-STUDIO350, Service Manual, Page: 72 / 286

Share
Download
Toshiba e-STUDIO350 Service Manual Download Page 72

e-STUDIO350/450  COPY PROCESS

3 - 4

November 2003 © TOSHIBA TEC

3

(5) Development

Development is the process of making the
electrostatic latent images visible to the eye
(visible images).

Developer material is supplied to the photo-
conductive drum surface by the magnetic roller.
The toner in the developer material adheres
to the areas on the drum surface where the
potential is lower than the developer bias which
is applied to the magnetic roller (reverse de-
velopment method).

Drum

Magnetic roller

Fig.3-207

Photoconductive layer

Magnet

Magnetic roller

Toner
Carrier (always attracted
onto the magnet)

Toner

Bias voltage
–550 VDC

Photocon-
ductive
drum

Aluminum base

Toner

Fig.3-208

The (–) potential of
the photoconductive
drum is higher than
the developer bias.

The (–) potential of
the photoconductive
drum is lower than
the developer bias.

0

– 100V

– 200V

– 300V

– 400V

– 600V

White background

Halftone

Solid

White background

Image not developed

Bias
potential

Image developed by
toner

750V

550V

Fig.3-209

Summary of Contents for e-STUDIO350































































































































































































































































































Reviews:

No comments