Toshiba e-STUDIO350 Service Manual Download Page 185

Page: 185 / 286

November 2003 © TOSHIBA TEC

10 - 3

e-STUDIO350/450 DRIVE SYSTEM

Level “H”

CCW direction

Abnormal rotation

Brake OFF

Motor OFF

Level “L”

CW direction

Normal rotation

Brake ON

Motor ON

Reference clock signal

10.3.2 Control signals

(1)

MAMCW signal (LGC

→

MTR: Input)

This is a signal to switch the direction of the main motor rotation. When this signal becomes “L” level,

the main motor rotates counterclockwise as seen from the rear side, and drives the developer unit,

drum, fuser unit, etc to the appropriate direction.

(2)

MAMPL signal (MTR

→

LGC: Output)

When the difference of the FG pulse cycle against the reference frequency is within ±6.25%, it is

specified that the motor is in a lock range (normal rotation), and this MAMPL signal becomes “L” level.

At this time, the LED “D4” is lit.

(3)

MAMCK signal (LGC

→

MTR: Input)

This is a reference clock signal to rotate the main motor at a fixed speed.

(4)

MAMBK signal (LGC

→

MTR: Input)

This is a signal to stop the main motor.

When it becomes “L” level, the main motor is braked.

(5)

MAMON signal (LGC

→

MTR: Input)

This is a signal to turn ON/OFF the main motor. When it becomes “L” level, the motor is rotated.

Signal level of the motor circuit

* The signal names are for the connector CN318(LGC board).

Signal

MAMCW

MAMPL

MAMCK

MAMBK

MAMON

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 185 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: