Toshiba e-STUDIO350 Service Manual Download Page 189

Page: 189 / 286

November 2003 © TOSHIBA TEC

11 - 1

e-STUDIO350/450 DRUM RELATED SECTON

11. DRUM RELATED SECTION

11.1 Configuration

This chapter explains about the area around the drum, drum itself, image processing, their parts and

control circuits.

This area mainly consists of the following components:

• Cleaner unit

Drum

Main charger

Cleaner

Cleaning blade

Toner recovery blade

Toner recovery auger

Toner bag full detection sensor -1

• Toner bag detection sensor -2

• Transfer / Separation charger

Transfer guide

Transfer charger

Separation charger

• Sub-separation fan / Exhaust fan

• Discharge LED

• Toner bag

• Developer unit cooling fan-1 / Developer unit cooling fan-2 / Middle fan

• Drum thermistor (in developer unit)

• High-voltage transformer

• Temperature/humidity sensor

Fig. 11-101

Discharge LED

Middle cooling fan

Toner recovery auger

Drum

Cleaning blade

Sub-separation fan

Exhaust fan

Separation
charger

Toner recovery blade

Transfer
charger

Transfer guide

Main charger

Drum thermistor

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 189 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: