Toshiba e-STUDIO350 Service Manual Download Page 177

Page: 177 / 286

November 2003 © TOSHIBA TEC

9 - 27

e-STUDIO350/450 PAPER FEEDING SYSTEM

Fig. 9-469

Fig. 9-468

Fig. 9-467

(5)

Take off the upper and lower transport clutch.

(Remove the gear and disconnect the con-

nector respectively, and then loosen the

setscrew to take them off.)

Notes:

Make sure that the upper and lower clutch are

different in size when installing them.

Upper side: Shaft diameter, 8 mm

Lower side: Shaft diameter, 6 mm

Attach the clutches to the shafts as shown on

the right.

0-0.5mm

[G] Drawer detection switch (upper/lower)

(1)

Remove the upper and lower drawers.

(2)

Take off the rear cover (

Chapter 2.5.1

[H]).

(3)

Take off the noise filter assembly (4 screws).

(4)

Take off the tray drive unit with its plate

(

Chapter 9.4 [E]).

(5)

Disconnect the connector, release the latch

and take off the drawer detection switch from

the front side.

Fig. 9-466

(4)

Remove 2 gears and disconnect 2 connec-

tors.

Connector

Gear

Upper transport clutch

Lower transport
clutch

Setscrew

Drawer detection switch

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 177 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: