Toshiba e-STUDIO350 Service Manual Download Page 106

Page: 106 / 286

e-STUDIO350/450 CONTROL PANEL

5 - 12

November 2003 © TOSHIBA TEC

5.5 Disassembly and Replacement

Note:

When taking off the control panel, check the

position of the stopper; if the stopper is at

the position “b”, remove the stopper or move

it to the position “a”.

Fig. 5-503

Fig. 5-504

[B] Control panel unit

(1) Take off the right upper cover and the front

upper cover ( Chapter 2.5.1 [J] [I]).

(2) Disconnect 1 connector.

(3) Remove 3 screws and take off 3 harness

clamps.

Fig. 5-501

[A] Stopper

(1) Slide the stopper and pull it out.

Fig. 5-502

Stopper

(4) Lower the control panel and remove 6 screws.

(5) Take off the control panel unit while sliding it.

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 106 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: