Toshiba e-STUDIO350 Service Manual Download Page 35

Page: 35 / 286

November 2003 © TOSHIBA TEC

2 - 19

e-STUDIO350/450 OUTLINE OF THE MACHINE

Function

Exposing the original to the light

Removing the residual charge from

the drum surface

Heating the fuser roller

Preventing condensation of the

mirrors of the carriages

*ASD/AUD/CND/SAD/TWD models:

Standard

*NAD/MJD models: Option

Preventing condensation of the lens

*ASD/AUD/CND/SAD/TWD models:

Standard

*NAD/MJD models: Option

Preventing condensation of the drum

*ASD/AUD/CND/SAD/TWD models:

Standard

*NAD/MJD models: Option

Name

LP-EXPO

Exposure lamp

LP-ERS

Discharge LED

IH-COIL

IH coil

SCN-L-DH

Scanner damp heater (Left)

SCN-R-DH

Scanner damp heater (Right)

DRM-DH

Drum damp heater

Symbol

EXP

ERS

IH-COIL

DH1

DH2

DH3

P-I

P21 - I6

P25 - I33

P31 - I23

P10 - I22

P10 - I32

P27 - I7

Remarks

B-1

D-2

B-2

D-2

(6)

Lamps and heaters

(7)

Thermistors and thermostats

Name

THMS-C-HTR

Main thermistor

THMS-S-HTR

Edge thermistor

THMS-DRM

Drum thermistor

THERMO-FSR

Fuser thermostat

THERMO-SCN-DH

Scanner damp heater thermostat

THERMO-DRM-DH

Drum damp heater thermostat

Symbol

THM1

THM2

THM3

THMO1

THMO2

THMO3

Function

Detecting the surface temperature at

the center part of the fuser roller

Detecting the surface temperature at

the edge of the fuser roller

Detecting the temperature at the drum

surface

Preventing overheating in the fuser

unit

Controlling the temperature of the

scanner damp heater

Controlling the temperature of the

drum damp heater

P-I

P29 - I10

P26 - I29

P29 - I9

P10 - I22

Remarks

D-2

B-2

D-2

P27 - I7

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 35 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: