Toshiba e-STUDIO350 Service Manual Download Page 223

Page: 223 / 286

November 2003 © TOSHIBA TEC

12 - 15

e-STUDIO350/450 DEVELOPMENT SYSTEM

Fig. 12-527

Fig. 12-528

Fig. 12-529

(I-2) Toner motor

(1)

Take off the toner cartridge drive unit

(

Chapter 12.5 (I-1)).

(2)

Remove 2 screws and take off the toner mo-

tor.

(I-3) Toner cartridge detection switch

(1)

Take off the toner cartridge drive unit

(

Chapter 12.5 (I-1)).

(2)

Remove 1 screw and take off the toner car-

tridge detection switch with the whole bracket.

(3)

Remove 3 screws with a fine screwdriver and

take off the toner cartridge detection switch

and switch cover.

<< Replacement of Oil Seal>>

Insert a fine screwdriver into the depression

of the oil seal to take it out.

Push in a new oil seal parallel to the frame or

bushing (shown figure at right).

Apply the grease (Alvania No.2; amount of 2

rice grains) on entire surface of the oil seal

evenly.

Note:

Wipe off the excessive grease.

Fig. 12-530

Outside

Inside

Oil seal

Grease

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 223 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: