Toshiba e-STUDIO350 Service Manual Download Page 52

Page: 52 / 286

e-STUDIO350/450 OUTLINE OF THE MACHINE

2 - 36

November 2003 © TOSHIBA TEC

Fig. 2-605

Fig. 2-606

Fig. 2-607

Fig. 2-608

(6)

Remove 2 screws on the front side.

(7)

Slide the RADF backward and take off by lift-

ing it up.

[B] KD-1011 (Paper Feed Pedestal (PFP))

(1)

Turn OFF the power and unplug the power

cable.

(2)

Remove 7 screws and take off the rear cover

of the equipment.

Note:

Disconnect the connector of the RADF first

when the RADF is installed.

(3)

Remove 1 screw and the ground wire, and then

disconnect 2 connectors (3 if the optional

damp heater is installed).

Connector of optional
damp heater

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 52 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: