Toshiba e-STUDIO350 Service Manual Download Page 171

Page: 171 / 286

November 2003 © TOSHIBA TEC

9 - 21

e-STUDIO350/450 PAPER FEEDING SYSTEM

Fig. 9-447

Fig. 9-446

Fig. 9-445

Fig. 9-444

(12) Remove 3 screws and take off the left trans-

port guide.

(13) Remove 2 screws and take off the registra-

tion front guide.

Note:

Be careful not to deform or damage the roller

supporting section when installing or taking

off the registration front guide.

(14) Remove 1 screw and take off the registration

sensor with bracket.

(15) Disconnect the connector, release the latch

to take off the registration sensor.

(16) Disconnect the connector, take off the upper

drawer feed sensor.

Screw

Registration
front guide

Roller supporting

section

Registration
sensor

Connector

Screw

Upper drawer
feed sensor

Connector

Left transport
guide

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 171 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: