Toshiba e-STUDIO350 Service Manual Download Page 165

Page: 165 / 286

November 2003 © TOSHIBA TEC

9 - 15

e-STUDIO350/450 PAPER FEEDING SYSTEM

Fig. 9-421

Fig. 9-422

Bypass pick up roller

Timing belt

Clip

Shaft

Clip

Bypass feed roller

(A-7) Bypass feed roller

(1)

Take off the bypass unit (

Chapter 9.4 (A-1)).

(2)

Take off the bypass feed upper cover

(

Chapter 9.4 (A-6)).

(3)

Take off the bypass drive unit (

Chapter

9.4 (A-6)).

(4)

Remove the clip, pull out the shaft and take

off the bypass feed roller.

Note:

Make sure the following items when assembling the

bypass feed roller and bypass pickup roller.

Set the timing belt to the pulley securely.

Do not put the wrong position when set

ting the timing belt.

Be sure to insert the clip into the groove of shaft.

Check that there is no stain such as oil on the

surface of timing belt, the pulley and the roller.

Install the bypass pickup roller and the

bypass feed roller in the correct direction.

Fig. 9-423

E-ring

Bushing

Bypass transport roller

Bushing

(A-8) Bypass transport roller

(1)

Take off the bypass feed upper cover

(

Chapter 9.4 (A-6)).

(2)

Take off the bypass drive unit (

Chapter

9.4 (A-6)).

(3)

Remove the E-ring, pull out the shaft and take

off the bypass transport roller.

(4)

Remove the clip, pull out the shaft and take

off the bypass pickup roller.

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 165 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: