Toshiba e-STUDIO350 Service Manual Download Page 222

Page: 222 / 286

e-STUDIO350/450 DEVELOPMENT SYSTEM

12 - 14

November 2003 © TOSHIBA TEC

(5)

Remove 1 bearing on the rear side and take

off the mixer-2.

*Replacement of Oil Seal (

Page 12-15)

Fig. 12-524

[I]

Toner cartridge drive unit

(I-1) Toner cartridge drive unit

(1)

Take off the toner cartridge.

(2)

Take off the developer unit

(

Chapter 12.5 [A]).

(3)

Take off the receiving tray

(

Chapter 2.5.1[H]).

(4)

Take off the tray back cover

(

Chapter 2.5.1 [I]).

Fig. 12-525

(7)

Remove 2 screws and disconnect 2 connec-

tors. Then take off the toner cartridge drive

unit.

Fig. 12-526

(5)

Disconnect 1 connector and remove 1 har-

ness clamp.

(6)

Remove 3 screws and take off the toner car-

tridge cover.

Bearing

Oil seal

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 222 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: