Toshiba e-STUDIO350 Service Manual Download Page 153

Page: 153 / 286

November 2003 © TOSHIBA TEC

9 - 3

e-STUDIO350/450 PAPER FEEDING SYSTEM

(1)

Pickup roller

This roller moves up and down to draw out a sheet of paper from the bypass tray or the drawer, and

transport it to the feed roller.

(2)

Feed roller

This roller transports the paper from the pickup roller to the registration roller.

(3)

Separation roller

This roller is mounted against the feed roller. When two sheets of paper or more are transported

from the pickup roller, the load of the torque limiter (spring) of the separation roller is greater than

the frictional force between the sheets. As the result, the separation roller is stopped and the lower

sheet of paper is not transported any further. When only one sheet of paper is transported from the

pickup roller, the separation roller is forced to rotate following the feed roller.

(4)

Transport roller

This roller transports the paper from the feed roller to the registration roller.

(5)

Registration roller

Paper transported from the feed roller is pushed against the registration rollers, which aligns the

leading edge of paper. The registration roller then rotates to transport the paper to the transfer

section.

The following sensors detect the presence/absence of paper and the position of the paper being trans-

ported, to control the ON/OFF of the corresponding rollers.

(6)

Bypass paper sensor

This sensor detects whether paper is set in the bypass tray or not. If it is, bypass feeding is per-

formed in preference to drawer feeding.

(7)

Bypass feed sensor

This sensor detects whether paper has been transported from the bypass tray or not. It also detects

whether the leading/trailing edge of paper has passed the feed sensor or not. This sensor is utilized

to detect the jams such as paper misfeeding in the bypass unit.

(8)

Drawer empty sensor

This is a transmissive-type sensor which detects the presence/absence of paper in the drawer

using an actuator. When there is no paper in the drawer, the actuator blocks the light path of the

sensor. Then the sensor determines that there is no paper.

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 153 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: