Toshiba e-STUDIO350 Service Manual Download Page 167

Page: 167 / 286

November 2003 © TOSHIBA TEC

9 - 17

e-STUDIO350/450 PAPER FEEDING SYSTEM

(A-11) Bypass feed sensor

(1)

Take off the bypass unit (

Chapter 9.4 (A-1)).

(2)

Take off the lower plate (

Chapter 9.4

(A-10)).

(3)

Remove 1 screw and take off the sensor plate.

(4)

Disconnect 1 connector, release the latch to

take off the bypass feed sensor.

Note:

Be careful not to come off the sensor arm and

the sensor spring after taking off the sensor.

Fig. 9-431

Fig. 9-430

Sensor plate

Screw

Sensor Spring

Sensor arm

Bypass feed sensor

(4)

Detach the cover, the arbor, and the clutch

spring from the shaft, and then take off the

bypass separation roller.

Fig. 9-429

Bypass separation
roller assembly

(3)

Take off the bypass separation roller assem-

bly.

Fig. 9-428

Shaft

Bypass separation roller

Cover

Clutch
spring

Arbor

Summary of Contents for e-STUDIO350






























































































































































































































































































Search results

Summary of Contents for e-STUDIO350

Reviews:

Toshiba e-STUDIO350, Service Manual, Page: 167 / 286

Search results

Summary of Contents for e-STUDIO350

Reviews: