manualshive.com logo in svg

Toshiba e-STUDIO350, Service Manual, Page: 221 / 286

Share
Download
Toshiba e-STUDIO350 Service Manual Download Page 221

November 2003 © TOSHIBA TEC

12 - 13

e-STUDIO350/450  DEVELOPMENT SYSTEM

12

Notes:

1.When installing the developer sleeve unit, make

sure that the side seals (urethane seal) of the

front and rear sides do not come out of the case.

2.When installing the doctor blade, make the gap

adjustment of the doctor sleeve.

Fig. 12-520

Fig. 12-521

Fig. 12-522

Fig. 12-523

[G] Mixer-1

(1)

Discharge the developer material

( 

 Chapter 12.5 (B-1)).

(2)

Take off the developer sleeve unit

 ( 

 Chapter 12.5 [F]).

(3)

Take off the bushing on the front side.

*Replacement of Oil Seal ( 

 Page 12-15)

(4)

Remove 1 E-ring and 1 bushing. Then take

off the mixer-1.

[H] Mixer-2

(1)

Discharge the developer material

( 

 Chapter 12.5 (B-1)).

(2)

Take off the developer sleeve unit

( 

 Chapter 12.5 [F]).

(3)

Remove 1 E-ring and 1 bushing on the front

side.

(4)

Remove 1 screw and holder.

*Replacement of Oil Seal ( 

 Page 12-15)

Holder

Oil seal

Bushing

Bushing

Oil seal

Bushing

Summary of Contents for e-STUDIO350































































































































































































































































































Reviews:

No comments