Toshiba E-Studio167 Page 71 Service Manual Download

Page: 71 / 266

e-STUDIO167/207/237

GENERAL OPERATION

4 - 3

4.2.3

Drawer feed copying

1) Press the [START] button

“READY” Æ “COPYING”

CIS LED ON

Scan motor ON

CIS unit move forward

Polygonal motor rotates in high speed

Main motor and exit motor ON

The drum, fuser unit, developer unit and exit roller are driven.

2) Drawer paper feeding

Main charger, developer bias and discharge LED ON. Fans are rotated in high speed. Pickup

solenoid ON.
-

Pickup roller start to rotate.

Pickup solenoid OFF after a certain period of time

Paper reaches the registration roller

The registration sensor is turned ON and aligning is performed.

3) After the scanning operation:

Registration clutch ON after a certain period of time

paper is transported to the transfer area

Copy counter operates

4) After the registration clutch is turned ON:

Transfer charger ON after a certain period of time

Copy counter operates

5) Completion of scanning

Scan motor OFF

CIS LED OFF

Registration clutch OFF (after the trailing edge of the paper passed the registration roller)

Ready state

6) Paper exit

Exit sensor detects the trailing edge of the paper

Main charger, developer bias and discharge LED OFF

Polygonal motor, main motor and exit motor OFF

Drum, fuser unit and developer unit stop

Fans return to the ready rotation

“READY” is displayed and the equipment enters the ready state

7) Timing chart for copying one A4 size sheet fed from the drawer

2354

2594

5009

2801

5103

4615

6921

4829

9400

Main motor

Registration clutch

MVDEN signal

Registration sensor

Exit sensor

(Unit : ms)

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands