manualshive.com logo in svg

Toshiba E-Studio167, Service Manual

The Toshiba E-Studio167 is a reliable and efficient multi-function copier/scanner/printer designed for small businesses. To ensure smooth operation and troubleshooting, we provide a comprehensive Service Manual that can be easily downloaded for free from manualshive.com. This manual is an essential resource for maintaining and optimizing the performance of your Toshiba E-Studio167.

Share
Download
background image

2

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

OUTLINE OF THE MACHINE

2 - 25

[D] Paper feed controller PC board (PFC)

Note: 

This paper feed controller PC board is optional for NAD, CND and MJD.

(3)

Disconnect 2 connectors, remove 1 screw, 
and then take off the fuse PC board by lifting 
it up.

 Fig. 2-28

(1)

Take off the rear cover.

"

 P.2-22 "[J] Rear cover"

(2)

Disconnect 2 connectors, remove 4 screws, 
and then take off the paper feed controller 
PC board and mylar sheet.

Notes: 

•

If the ADU (optional) is installed, discon-
nect 2 connectors of the ADU with other 
connectors at the same time before tak-
ing off the paper feed controller PC board.

•

If the PFP (optional) is installed, discon-
nect 2 connectors of the PFP with other 
connectors at the same time before tak-
ing off the paper feed controller PC board.

 Fig. 2-29

Connector

Fuse PC board

Connector (PFP)

Connector (ADU)

Paper feed controller 
PC board

Connector 

Mylar

Summary of Contents for E-Studio167











































































































































































































































































Reviews:

No comments

Related manuals for E-Studio167

Oki 6150 Setup Manual preview
6150
Brand: Oki Pages: 40
Radio Shack DMP-200 Operation Manual preview
DMP-200
Brand: Radio Shack Pages: 62
QMS 1060 User Manual preview
1060
Brand: QMS Pages: 311
Citizen CMP-10 Command Reference Manual preview
CMP-10
Brand: Citizen Pages: 80
Microplex SOLID T11 DT Operator'S Manual preview
SOLID T11 DT
Brand: Microplex Pages: 135
Phoenix Contact THERMOMARK CARD User Manual preview
THERMOMARK CARD
Brand: Phoenix Contact Pages: 35
Oki 431dn+ User Manual preview
431dn+
Brand: Oki Pages: 138
Lexmark MS510dn Supplies Manual preview
MS510dn
Brand: Lexmark Pages: 2
A&D AD-8118B Instruction Manual preview
AD-8118B
Brand: A&D Pages: 102
Sharp MX-6500N Media Manual preview
MX-6500N
Brand: Sharp Pages: 38
Canon PIXMA MX712 Guía De Configuración preview
PIXMA MX712
Brand: Canon Pages: 22
Canon PIXMA MX512 Getting Started Manual preview
PIXMA MX512
Brand: Canon Pages: 4
Canon PIXMA MP970 Setup Instructions preview
PIXMA MP970
Brand: Canon Pages: 2
Canon PIXMA MX432 Getting Started Manual preview
PIXMA MX432
Brand: Canon Pages: 4
Canon MP560 - PIXMA Color Inkjet Function Manual preview
MP560 - PIXMA Color Inkjet
Brand: Canon Pages: 12
Canon PIXMA MX512 Guía De Configuración preview
PIXMA MX512
Brand: Canon Pages: 21
Canon PIXMA MX350 Network Setup Manual preview
PIXMA MX350
Brand: Canon Pages: 34
Canon PIXMA MX522 Easy Setup preview
PIXMA MX522
Brand: Canon Pages: 2

Brands by name

Popular brands

Load more brands