manualshive.com logo in svg

Toshiba E-Studio167, Service Manual

The Toshiba E-Studio167 is a reliable and efficient multi-function copier/scanner/printer designed for small businesses. To ensure smooth operation and troubleshooting, we provide a comprehensive Service Manual that can be easily downloaded for free from manualshive.com. This manual is an essential resource for maintaining and optimizing the performance of your Toshiba E-Studio167.

Share
Download
background image

e-STUDIO167/207/237

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

COPY PROCESS

3 - 12

10)Discharging

Discharging is the process of eliminating the negative charge remaining on the photoconductive 
drum before the next charging process.
If the residual charge is not eliminated, the following phenomenon occurs:

Negative charge remaining on the photoconduc-
tive drum surface causes ungiven application of 
the charge for the next printing.

#

 Fig. 3-22

The next print will have a double image. (The 
preceding image appears.)

#

Solution:
The entire surface of the photoconductive drum 
is illuminated with light by the discharge LED 
array.

#

The photoconductive drum becomes electri-
cally conductive.

#

All of the negative charge remaining on the pho-
toconductive drum is conducted to the ground.

#

Preparation for the next printing is completed.

Discharge LED

Photoconductive
drum

Ground

Summary of Contents for E-Studio167











































































































































































































































































Reviews:

No comments

Related manuals for E-Studio167

Canon BJC-S530D Quick Start Manual preview
BJC-S530D
Brand: Canon Pages: 96
Canon BJC-S500 Setup Instructions preview
BJC-S500
Brand: Canon Pages: 2
Canon BJC-S300 Setup Instructions preview
BJC-S300
Brand: Canon Pages: 2
Canon BJC-80 Specification preview
BJC-80
Brand: Canon Pages: 2
Canon BJC-6000 Series Setup Instructions preview
BJC-6000 Series
Brand: Canon Pages: 10
Canon BJC-55 Series Specification preview
BJC-55 Series
Brand: Canon Pages: 2
Canon BJC-5100 Series Technical Information preview
BJC-5100 Series
Brand: Canon Pages: 2
Canon BJC-50 Parts Catalog preview
BJC-50
Brand: Canon Pages: 4
Canon BJC-4400 Series Quick Start Manual preview
BJC-4400 Series
Brand: Canon Pages: 15
Canon BJC-3000 Series Quick Start Manual preview
BJC-3000 Series
Brand: Canon Pages: 8
Canon BJC-3000 Series Technical Information preview
BJC-3000 Series
Brand: Canon Pages: 2
Canon BJC-2100 Series Quick Start Manual preview
BJC-2100 Series
Brand: Canon Pages: 9
Canon BJC S600 Setup Instructions preview
BJC S600
Brand: Canon Pages: 11
Canon BJC-2100 Series Simplified Manual preview
BJC-2100 Series
Brand: Canon Pages: 9
Canon BJC-55 Series Service Manual preview
BJC-55 Series
Brand: Canon Pages: 206
Canon 900D - i Color Inkjet Printer Printing Manual preview
900D - i Color Inkjet Printer
Brand: Canon Pages: 30
Canon 8996A001 - i 455 Color Inkjet Printer Printing Manual preview
8996A001 - i 455 Color Inkjet Printer
Brand: Canon Pages: 4
Canon 820D - S Color Inkjet Printer Application Manual preview
820D - S Color Inkjet Printer
Brand: Canon Pages: 140

Brands by name

Popular brands

Load more brands