Toshiba E-Studio167 Service Manual Download Page 141

Page: 141 / 266

e-STUDIO167/207/237

DRIVE UNIT

9 - 9

(7)

Take off the gear and timing belt from the
main motor drive unit.

Notes:

•

Do not apply more tension to the belt of
the main motor drive unit than that pro-
duced by the spring force.

•

Follow the procedure bellow to perform
tension adjustment when assembling the
main motor drive unit.
-

Align the tensioner with the punch
mark and tighten the tensioner fixing
screw.

Hook the tensioner spring.

Install the main motor drive unit to the
equipment.

Loosen the tensioner fixing screw.

Let the spring force produce tension
for the belt, and tighten the fixing
screw.

Fig. 9-10

Fig. 9-11

Gear

Timing belt

Main motor drive unit

Tensioner spring

Tensioner

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands