Toshiba E-Studio167 Page 198 Service Manual Download | Manualshive

Page: 198 / 266

background image

e-STUDIO167/207/237

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

DEVELOPMENT SYSTEM

12 - 6

12.3.3

Recovered toner supply mechanism

The toner scraped off by the drum cleaning blade is transported by the toner recovery auger and the
toner recycling auger to be recycled, and then returned into the developer unit. Then the recovered
toner in the developer unit is mixed by the developer material using the mixer-3. The mixer-3 is
mounted exclusively for the recovered toner to mix it in a sufficient period of time. On the other hand,
the (fresh) toner transported from the toner cartridge into the developer unit is mixed by the mixer-2.
Then the (fresh) toner and the recovered toner are mixed together and further transported to the mixer-
1. They are further mixed by the mixer-1 and transported to the developer sleeve.

Fig. 12-2

Drum cleaner

Mixer-1

Mixer-2

Toner recycling auger

Fresh toner
Recovered toner

Toner cartridge

Mixer-3

Toner recovery auger

«
...
196
197
198
199
200
...
»

Summary of Contents for E-Studio167











































































































































































































































































Reviews:

No comments

Related manuals for E-Studio167

imagePROGRAF iPF8300S

Brand: Canon Pages: 52

Brand: Canon Pages: 2

Brand: Oki Pages: 48

Brand: Oki Pages: 34

Brand: Oki Pages: 65

Brand: Oki Pages: 44

Brand: Oki Pages: 36

Brand: OHAUS Pages: 28

Brand: Oce Pages: 396

Brand: Oce Pages: 28

Brand: Oki Pages: 64

Brand: Samsung Pages: 199

Brand: DNP Pages: 2

Brand: Citizen Pages: 80

Brand: Ricoh Pages: 159

Brand: A&D Pages: 32

Brand: Oki Pages: 187

Brand: Oki Pages: 336

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands