Toshiba E-Studio167 Service Manual Download Page 182

Page: 182 / 266

e-STUDIO167/207/237

DRUM RELATED SECTION

11 - 12

[D] Main charger

[E]

Main charger grid

(3)

Release the harness from the harness clamp
and pull out the discharge LED.

Fig. 11-14

(1)

Take off the discharge LED unit.

P.11-11 "[C] Discharge LED (ERS)"

(2)

Pull out the main charger and take it off by
sliding it to the rear side.

Note:

Be careful not to touch or scratch the drum
surface at this time.

Fig. 11-15

(1)

Take off the main charger.

P.11-12 "[D] Main charger"

(2)

Remove the spring and take off the main
charger grid.

Note:

Do not touch the mesh area of the grid.

Fig. 11-16

Discharge LED

Main charger

Main charger grid

Spring

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands