Toshiba E-Studio167 Service Manual Download Page 169

Page: 169 / 266

e-STUDIO167/207/237

PAPER FEEDING SYSTEM

10 - 27

(3)

Take off the damp heater unit or dummy
plate.

P.10-19 "[J] Damp heater unit (DH3) /

Dummy plate"

(4)

Take off the registration roller (metal).

P.10-25 "[Q] Registration roller (metal)"

(5)

Remove 1 screw.

Fig. 10-53

(6)

Take off the registration guide while lifting it
up. Release the latch and take off the drawer
detection switch bracket.

Note:

Be careful not to break the harness which
connects the registration guide unit with the
drawer detection switch when taking off the
unit.

Fig. 10-54

(7)

Take off the bracket of paper empty sensor.

P.10-20 "[K] Paper empty sensor (S7)"

(8)

Release the harness from the harness
clamp, disconnect the connector, remove 3
screws, and then take off the registration
guide.

Fig. 10-55

Screw

Registration guide unit

Drawer detection
switch bracket

Connector

Registration guide

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands