Toshiba E-Studio167 Service Manual Download Page 200

Page: 200 / 266

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 8

12.5 Auto-Toner Circuit

12.5.1

General description

1) Function of the auto-toner circuit

Detects the toner density in the developer material, and supplies toner when the density is low-
ered to a certain level.

Detects that there is no toner left in the cartridge (toner-empty detection).

2) The auto-toner circuit consists of the following:

Auto-toner sensor:
Detects the toner density.

Control section:
Controls the toner density so that the toner in the developer material is fixed to certain ratio.

Toner motor:
Supplies toner to the developer material.

Control panel:
Indicates toner-empty information.

Recovered toner supply section:
The main motor supplies the recovered toner to the developer unit from the recovered toner sup-
ply mechanism.

Fig. 12-4

Toner

Developer material

Auto-toner sensor

Toner cartridge

Recovered toner

supply section

Temperature/humidity sensor

Toner
motor

Recovered

toner

Recovered toner

supply mechanism

Main

motor

A/D

converter

D/A

converter

ASIC

SoC

Flash ROM

Control panel

Control section

MAIN board

Developer unit

Control voltage signal

Toner density signal

"Toner Empty"

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands