Toshiba E-Studio167 Service Manual Download Page 116

Page: 116 / 266

e-STUDIO167/207/237

SCANNER

6 - 24

[H] CIS case

(4)

Lift up the CIS unit, disconnect 1 connector
on the bottom of the CIS unit, and then take
off the CIS unit.

Notes:

•

Take care not to contaminate the CIS unit
surface with fingerprints, dust or such.

•

Be sure to perform "05-310" with the
platen cover or the ADF/RADF closed
after replacing the CIS unit.

Fig. 6-30

(5)

Release 2 latches each to take off 2 original
glass guides from the CIS unit.

Fig. 6-31

(1)

Take off the CIS unit.

P.6-23 "[G] CIS unit (CIS)"

(2)

Remove 1 screw and take off the belt stop-
per.

Note:

When installing the belt stopper, install it so
that the protrusion of the stopper fits in the V-
groove on the inside of the CIS unit drive
belt-1.

Fig. 6-32

CIS unit

Connector

Original glass guide

Belt stopper

CIS unit
drive belt-1

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands