Toshiba E-Studio167 Service Manual Download Page 70

Page: 70 / 266

e-STUDIO167/207/237

GENERAL OPERATION

4 - 2

4.2

Description of Operation

4.2.1

Warming-up

1) Initialization

Power ON

Heater lamp ON

“Please wait” is displayed

Fan motors ON

Initialization of scanning system

The CIS unit moves to the home position.

The CIS unit moves to the peak detection position.

The LED of CIS is turned ON.

Peak detection (white color is detected by the shading correction plate)

The LED of CIS is turned OFF.

The CIS unit moves to the home position.

“READY (WARMING UP)” is displayed

2) Pre-running operation (Only when the temperature is at 16 °C or less)

The pre-running operation is started when the temperature of the fuser roller surface reaches a cer-
tain temperature.

The main motor is turned ON

Fuser roller rotated.

Drum rotated.

Pre-running operation stops after 15 seconds

3) When the surface temperature of the fuser roller becomes sufficient for fusing,

“READY” is displayed

4.2.2

Ready state (ready for copying)

Buttons on the control panel enabled

When no button is pressed for a certain period of time,

- Set number “1” is displayed. Equipment returns to the normal ready state.

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Toshiba E-Studio167, Service Manual, Page: 70 / 266

Search results

Summary of Contents for E-Studio167

Reviews: