manualshive.com logo in svg

Toshiba E-Studio167, Service Manual, Page: 201 / 266

Share
Download
Toshiba E-Studio167 Service Manual Download Page 201

12

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 9

12.5.2

Function of auto-toner sensor

1) Function

-

Initialization adjustment function - At the first use of the equipment or when the developer mate-
rial is replaced with a new one.
Automatically adjusts the output value of the auto-toner sensor responding to humidity (input 
value to the A/D converter) for the toner density of the new developer material so that it stays in 
range of 2.34 to 2.46 V.

-

Stabilizing the toner density - During the printing operation
Maintains the toner density to a certain ratio as follows.

Toner is consumed.

 !

The toner density is lowered.

 !

Change in the auto-toner sensor output responding to humidity is detected.

 !

The toner motor is driven.

 !

Toner is supplied from the toner cartridge to the developer unit.

-

Toner-empty detection and recovery:

Detects that there is no toner in the toner cartridge:
The toner motor is driven.

 !

The auto-toner sensor output does not change.

 !

The toner density does not change.

 !

It is determined there is no toner in the cartridge (toner empty).

Recovering from the toner-empty state:
The toner motor is driven.

 !

Toner is supplied from toner cartridge.

 !

The auto-toner sensor output changes.

 !

The toner density returns to normal value.

 !

The toner-empty state is cleared.

Summary of Contents for E-Studio167











































































































































































































































































Reviews:

No comments