Toshiba E-STUDIO 232 Operator'S Manual Download Page 272 | Manualshive

Page: 272 / 354

background image

270

8.JOB STATUS

6.Error Code (Cont.)

8

2D43

Encryption error.
Failed to create file.

Perform the job in error again. If the error still occurs, turn the
power OFF and then back ON. Perform the job in error again.

2D60

Failed to copy file

Turn the power OFF and then back ON. Retry the scan. If the
error still occurs, contact your service representative.

2D62

Failed to connect to
network destination.
Check destination
path.

Check destination path.
Make sure that the network path is correct, and retry the scan. If
the error still occurs, ask your administrator to confirm whether
the IP address or path of the server is correct. Also make sure
that the server is operating properly.

2D63

Specified network path
is invalid. Check desti-
nation path.

Make sure you specify correct network folder and retry the scan.

2D64

Logon to file server
failed. Check user-
name and password.

Make sure you specify correct user name and password to
logon the file server and retry the scan.

2D65

There are too many
documents in the
folder. Failed in creat-
ing new document.

Delete the data in the local storage folder in the equipment and
retry the scan.

2D66

Failed to process your
job. Insufficient stor-
age space.

Delete the data in the local storage folder in the equipment and
retry the scan.

2D67

FTP service is not
available.

Ask your administrator whether the FTP service is configured
correctly.

2D68

File sharing service is
not available.

Ask your administrator whether the SMB protocol is enabled.

2DA8

The HDD is running
out of capacity for the
shared folder.

Delete the unnecessary data in HDD.

2DC0

Job cancelled.

Job was cancelled.

2DC1

Power failure
occurred.

Make sure that the power cable is connected properly and it is
inserted securely. Resend the job.

Store to e-Filing

2B10

There was no applica-
ble job.

Turn the power OFF and then back ON. Retry the scan. If the
error still occurs, contact your service representative.

2B11

Job status failed.

Turn the power OFF and then back ON. Retry the scan. If the
error still occurs, contact your service representative.

2B20

Failed to access file

Turn the power OFF and then back ON. Retry the scan. If the
error still occurs, contact your service representative.

2B21

Message size
exceeded limit or maxi-
mum size

Fragment the message into several smaller-sized ones and
send them again.

2B30

Insufficient disk space

Delete unnecessary documents in e-Filing and try again.

Error code

Problem

What to do

«
...
270
271
272
273
274
...
»

Summary of Contents for E-STUDIO 232



































































































































































































































































































































































Reviews:

No comments

Related manuals for E-STUDIO 232

Brand: Oki Pages: 282

Brand: Oki Pages: 48

Brand: Panasonic Pages: 102

Brand: F+D Feinwerk- und Drucktechnik Pages: 41

Brand: Konica Minolta Pages: 32

Brand: Ricoh Pages: 4

Brand: Felix printers Pages: 26

Brand: Oki Pages: 132

BradyPrinter A5500

Brand: Brady Pages: 72

Brand: Ricoh Pages: 2

Brand: SPRT Pages: 18

Brand: Aficio Pages: 92

Automatic Photo Book Station

Brand: Durst Pages: 2

Brand: Printronix Pages: 148

Brand: Epson Pages: 105

Brand: Epson Pages: 128

Brand: Epson Pages: 145

Brand: Epson Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands