Touche
☼
: Permet d’activer et de désactiver le rétroéclairage: EIN-AUS (allumé/éteint) (uniquement
pour l’afficheur LCD), ON, OFF, ON-OFF.
Touche
PLU
: Permet de sélectionner le prix unitaire.
Touches
P1, P2
...: Servent à sélectionner rapidement un prix unitaire.
Touche ↓: (MAJ) Sert à sélectionner les programmes
P16
-P30.
PREMIÈRE MISE SOUS TENSION
Lorsque la balance est mise sous tension, tous les symboles et éléments sont visibles. Le compte à
rebours est visible pendant environ 10 secondes. Ensuite, vous voyez la charge maximale admissible,
puis la balance et le poids passent en mode de fonctionnement normal. L’afficheur indique zéro. Les
symboles
et
sont actifs. Le plateau ne doit être chargé que lorsque la balance est prête
pour la pesée. Si le plateau est déjà chargé ou qu’aucun plateau n’est installé, l’erreur « nnnnnn »
peut apparaître sur l’afficheur. Assurez-vous que le plateau n’est pas chargé avant d’appeler le
service d’assistance.
PESÉE
Posez la charge sur le plateau de la balance
. Attendez que le témoin D s’allume. Le poids de la
charge apparait sur l’afficheur.
Lorsque le plateau est vide, la valeur « 0,000 » devrait apparaître sur l’afficheur et les témoins
et
devraient s’allumer. Si la valeur affichée n’est pas nulle ou si le témoin
ne s’allume pas,
appuyez sur
pour effacer la valeur relevée. Une fois la balance remise à zéro et stabilisée, le
fonctionnement normal peut débuter.
ATTENTION: Il est interdit de poser des objets d’un poids supérieur à la charge maximale admissible
de la balance sur celle-ci. (Valeur « Max »: voir la plaque signalétique) Posez la charge à la main sur le
plateau. Le fait de lancer une charge sur le plateau à partir d’un point de même hauteur ou d’un
point plus élevé peut endommager la balance (même si la charge est légère).
PESÉE AVEC PRIX UNITAIRES
Si un prix unitaire a été saisi lors de la pesée, le montant à payer est calculé automatiquement. Le
prix unitaire peut être saisi de deux façons:
• Touches numériques « 0 », « 1 »... « 9 ».
• Touche de recherche de prix P1, P30.
• Le prix unitaire devrait être visible sur l’afficheur de prix unitaire et le montant à payer sur
l’afficheur du montant à payer.
Appuyez sur la touche ↓ (MAJ) pour sélectionner
les
programmes P16 à P30.
REMARQUE: Le prix unitaire peut être entré comme nombre entier ou comme fraction.
Exemple: Si le prix unitaire est de 75,9, appuyez sur
1. La touche « 7 »
2. La touche « 5 »
Summary of Contents for EX10200006
