Posez le produit sur le plateau de la balance. Attendez jusqu’à ce que le témoin
apparaisse.
Appuyez sur la touche M+. Le témoin M correspondant clignote.
ATTENTION: Pendant la remise à zéro de la balance, quand une valeur négative s’affiche et quand le
témoin
n’est pas visible, aucune donnée ne peut être ajoutée dans la mémoire.
ATTENTION: Après l’ajout d’une opération dans la mémoire, il n’est pas possible d’ajouter la valeur
correspondante dans la mémoire si le plateau n’est pas vide. L’afficheur n’indique pas la valeur «
0.000 » ou un nouveau prix unitaire est entré.
REMARQUE: Vous pouvez vérifier la valeur totale en appuyant sur la touche M+. Pour cela, il faut
désactiver la fonction « Adding without Showing Total » (Set 3-1) dans les réglages « SETTINGS ». La
valeur totale reste alors visible jusqu’à ce que le produit soit retiré du plateau.
REMARQUE: Il est possible de sauvegarder jusqu’à 250 promotions pour les ajouter à la mémoire.
Affichage et suppression des données en mémoire:
Appuyez sur la touche MR/MC. L‘espace de deux secondes, l‘afficheur indique « Top AG », puis il
indique le poids total l’espace de deux secondes. Appuyez sur la touche MR/MC Effacez la mémoire,
ou appuyez sur F pour revenir au mode de pesée normal.
Le témoin de mémoire s’affiche sous forme de M:
Si le témoin est éteint: la mémoire est vide.
Si le témoin clignote: les données enregistrées sont stockées dans la mémoire.
Si le témoin est allumé: la valeur de la mémoire est visible.
Affichage des données en mémoire:
Appuyez sur la touche MR/MC. L‘espace de deux secondes, l‘afficheur indique « Top AG », puis il
indique le poids total l’espace de deux secondes. Appuyez sur la touche M+. L‘espace de de deux
secondes, l‘afficheur indique « TP I », puis il indique le poids qui a été pesé en premier. Une pression
sur la touche M+ fait apparaître les promotions correspondantes. L‘espace de deux secondes,
l‘afficheur indique « Top AG », puis il indique le poids total l’espace de deux secondes. Appuyez sur la
touche MR/MC pour effacer la mémoire ou appuyez sur F pour revenir à la pesée sans supprimer de
données.
RÉTROÉCLAIRAGE DE L’AFFICHEUR
Appuyez trois fois sur
☼
pour faire passer le rétroéclairage de ON, à OFF, puis à ON_OFF. Pour
modifier le mode de rétroéclairage, procédez comme suit:
Le mode de rétroéclairage apparaît sur l’afficheur pendant environ une seconde:
bL Ein/On:le rétroéclairage est ALLUMÉ Le rétroéclairage est activé en continu.
bL OFF: le rétroéclairage est ÉTEINT. Le rétroéclairage demeure éteint en continu.
bLOnFF: le rétroéclairage est activé en mode ON_OFF. Le rétroéclairage s’allume lors de la pesée et
lorsqu’une touche est enfoncée. L’éclairage s’éteint quand le plateau est vide. Lorsque la balance est
allumée, le rétroéclairage est éteint. Lorsque le témoin clignote au niveau du poids, le rétroéclairage
s’éteint automatiquement.
Summary of Contents for EX10200006
