Tektronix CMD 80, User Manual

Page: 504 / 672

Appendix F: Remote Control Command Tables
F–68
CMD 80 Digital Radiocommunication Tester User Manual
Analog Manual Test (Signaling) Commands
Table F–11: Analog manual test (signaling) commands
Command Values State Notes
Unregistered and Registered States – General Measurements
CONFigure:AIACcess:ASTop <OFF | ON>
Establishes the auto stop state for the standby power measurement done while in the Analog
Idle or Access states, ie. the Unregistered or Registered states.
ALL
CONFigure:AIACcess:ASTop? ALL
CONFigure:AIACcess:LIMit:POWer:STANdby[:UPPer] <maximum mobile station standby
power [DBM]>
Establishes the limit for the standby power measurement done while in the Analog Idle or
Access states, ie. the Unregistered or Registered states.
–80.0 dBm to
–60.0 dBm to
–40.0 dBm ALL
CONFigure:AIACcess:LIMit:POWer:STANdby[:UPPer]? ALL
CONFigure:AIACcess:[SETTings]:DEFault
Resets all Analog standby power settings to the default values.
ALL
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á
Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
READ[:SCALar]:AIACCess:POWer:ACTive?
Measures and returns the active access power measured during the Analog Idle or Access
states, ie. the Unregistered or Registered states. A similar command exists for CDMA.
ÁÁÁÁÁÁ
Á ÁÁÁÁ Á
Á ÁÁÁÁ Á
ÁÁÁÁÁÁ
See note
ÁÁÁÁ
Á ÁÁ Á
Á ÁÁ Á
ÁÁÁÁ
AMID
ÁÁÁ
Á Á Á
Á Á Á
ÁÁÁ
1
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á
Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
READ[:SCALar]:AIACCess:POWer:STANdby?
Measures and returns the standby access power measured during the Analog Idle or Access
states, ie. the Unregistered or Registered states. A similar command exists for CDMA.
ÁÁÁÁÁÁ
Á ÁÁÁÁ Á
Á ÁÁÁÁ Á
ÁÁÁÁÁÁ
See note
ÁÁÁÁ
Á ÁÁ Á
Á ÁÁ Á
ÁÁÁÁ
AMID
ÁÁÁ
Á Á Á
Á Á Á
ÁÁÁ
2
FETCh[:SCALar]:AIACCess:POWer:STANdby:LIMit:FAIL?
Returns the pass/fail value for the standby power measurement done while in the Analog Idle
or Access states, ie. the Unregistered or Registered states.
ALL
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
FETCh[:SCALar]:MSINfo[:ALL]?
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
See note
ÁÁÁÁ
ÁÁÁÁ
ALL
ÁÁÁ
ÁÁÁ
3
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Call Established State – General Measurements
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á
Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
CONFigure:ACEQuality:LIMit:ERRor:CFRequency <carrier frequency error range [HZ]>
Frequency difference between the expected and measured carrier frequency.
ÁÁÁÁÁÁ
Á ÁÁÁÁ Á
Á ÁÁÁÁ Á
ÁÁÁÁÁÁ
0 Hz to 4000 Hz
to 10000 Hz
ÁÁÁÁ
Á ÁÁ Á
Á ÁÁ Á
ÁÁÁÁ
ALL
ÁÁÁ
Á Á Á
Á Á Á
ÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
CONFigure:ACEQuality:LIMit:ERRor:CFRequency?
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ALL
ÁÁÁ
ÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
CONFigure:ACEQuality:LIMit:ERRor:FREQuency:SAT <SAT frequency error range [HZ]>
Maximum frequency error allowed for SAT. (Expected frequency
±
this number.)
ÁÁÁÁÁÁ
Á ÁÁÁÁ Á
ÁÁÁÁÁÁ
0 Hz to 1 Hz to
500 Hz
ÁÁÁÁ
Á ÁÁ Á
ÁÁÁÁ
ALL
ÁÁÁ
Á Á Á
ÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
CONFigure:ACEQuality:LIMit:ERRor:FREQuency:SAT?
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ALL
ÁÁÁ
ÁÁÁ
1
The result returned is the measured power of the last access probe sent by the mobile station.
2
The result returned is the measured power of the mobile station between access probes.
3
The results returned are: mobile station identification number, serial number, and power class. The values of the mobile
station identification number and the serial number are determined by what has been programmed into the mobile
station.