68
www.stiebel-eltron.CoM
aIr | watEr HEat pUmp wpl 10
A
t a glance
For fully automatic heating
water heating up to +60 °C flow
temperature
suitable for underfloor heating
systems and systems with
radiators; low temperature
heating systems are preferred, as
these achieve a higher coefficient
of performance
extracts energy from the outside
air, right down to -20 °C outside
temperature
Comprises all components
required for its function and
safety
Central control of the heating
system and safety functions
through the heat pump manager
(essential accessory)
Corrosion-protected, external
casing panels made from zinc-
plated sheet steel with a stove
enamelled finish; internal airways
made from corrosion-resistant
aluminium sheet
Compact design, therefore modest
space requirements for internal or
external installations
test symbol of independent test
bodies (see type plate)
Contains non-combustible r407C
safety refrigerant
Function
Heat is extracted from the outside air
at temperatures ranging from +30 °C
to –20 °C by the heat exchanger
on the air side (evaporator).
Heating water is heated in the
heat exchanger on the water side
(condenser) to levels set at the
control unit (from +15 °C to +60 °C)
by heat from the electrical power
used by the compressor. At air
temperatures below approx. +7 °C,
the humidity in the air precipitates as
hoarfrost on the evaporator fins. Any
hoarfrost is automatically defrosted.
water created from this defrosting
collects in the defrost pan and is
drained off via a hose. the fan is
switched oFF and the heat pump
circuit is reversed to activate the
defrost cycle. the energy required for
defrosting is drawn from the heating
system. the heat pump automatically
reverts to heating mode at the end of
the defrost cycle.
Appliance description WPL 10 A
Compact version for external
installation. the metal enclosure is
zinc-plated and finished in pearl-
white stove enamel. the heat
pump drive unit is equipped with
a hermetically sealed compressor
with crankcase heater, condenser,
evaporator, safety equipment such
as a high/low pressure limiter, and
a frost protection facility. Heating
water up to 75 °C can flow through
the heat pump in idle mode. the
refrigerant used is r407C. the heat
pump is controlled via a bUs cable.
Safety and quality
Appliance description WPL 10 IA
Compact version for internal
installation. the metal enclosure is
zinc-plated and finished in pearl-
white stove enamel. the heat
pump drive unit is equipped with
a hermetically sealed compressor,
condenser, evaporator, safety
equipment such as a high/low
pressure limiter, expansion vessel,
integral control unit, integral diverter
valve for DHw heating and a frost
protection facility. Heating water up
to 75 °C can flow through the heat
pump in idle mode. the refrigerant
used is r407C.
Appliance description WPL 10 I
Compact version for internal
installation. the metal enclosure
is zinc-plated and finished in
pearl-white stove enamel. the
heat pump drive unit is equipped
with a hermetically sealed
compressor, condenser, evaporator,
safety equipment such as a high/
low pressure limiter, and a frost
protection facility. Heating water up
to 75 °C can flow through the heat
pump in idle mode. the refrigerant
used is r407C. the heat pump is
controlled via a bUs cable.
Summary of Contents for Heat pumps
