manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 126 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 126

   

   

   

Connectivity line devices: reset and clock control (RCC)

RM0008

126/1096

 Doc ID 13902 Rev 12

Calibration

RC oscillator frequencies can vary from one chip to another due to manufacturing process 
variations, this is why each device is factory calibrated by ST for 1% accuracy at T

A

= 25 °C.

After reset, the factory calibration value is loaded in the HSICAL[7:0] bits in the 

Clock control 

register (RCC_CR)

. 

If the application is subject to voltage or temperature variations this may affect the RC 
oscillator speed. You can trim the HSI frequency in the application using the HSITRIM[4:0] 
bits in the 

Clock control register (RCC_CR)

.

The HSIRDY flag in the 

Clock control register (RCC_CR)

 indicates if the HSI RC is stable or 

not. At startup, the HSI RC output clock is not released until this bit is set by hardware. 

The HSI RC can be switched on and off using the HSION bit in the 

Clock control register 

(RCC_CR)

.

The HSI signal can also be used as a backup source (Auxiliary clock) if the HSE crystal 
oscillator fails. Refer to 

Section 8.2.7: Clock security system (CSS) on page 128

.

8.2.3 PLLs

The main PLL provides a frequency multiplier starting from one of the following clock 
sources:

●

HSI clock divided by 2

●

HSE or PLL2 clock through a configurable divider

Refer to 

Figure 11

 and 

Clock control register (RCC_CR)

. 

PLL2 and PLL3 are clocked by HSE through a specific configurable divider. Refer to 

Figure 11

 and 

Clock configuration register2 (RCC_CFGR2)

The configuration of each PLL (selection of clock source, predivision factor and 
multiplication factor) must be done before enabling the PLL. Each PLL should be enabled 
after its input clock becomes stable (ready flag). Once the PLL is enabled, these parameters 
can not be changed.

When changing the entry clock source of the main PLL, the original clock source must be 
switched off only after the selection of the new clock source (done through bit PLLSRC in 
the Clock configuration register (RCC_CFGR)).

An interrupt can be generated when the PLL is ready if enabled in the 

Clock interrupt 

register (RCC_CIR)

.

8.2.4 LSE 

clock

The LSE crystal is a 32.768 kHz Low Speed External crystal or ceramic resonator. It has the 
advantage providing a low-power but highly accurate clock source to the real-time clock 
peripheral (RTC) for clock/calendar or other timing functions. 

The LSE crystal is switched on and off using the LSEON bit in 

Backup domain control 

register (RCC_BDCR)

. 

The LSERDY flag in the 

Backup domain control register (RCC_BDCR)

 indicates if the LSE 

crystal is stable or not. At startup, the LSE crystal output clock signal is not released until 
this bit is set by hardware. An interrupt can be generated if enabled in the 

Clock interrupt 

register (RCC_CIR)

.

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments