manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 781 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 781

RM0008

Universal synchronous asynchronous receiver transmitter (USART)

Doc ID 13902 Rev 12

781/1096

   

   

   

Figure 289. USART data clock timing diagram (M=1)

Figure 290. RX data setup/hold time

Note:

The function of CK is different in Smartcard mode. Refer to the Smartcard mode chapter for 
more details.

27.3.10 

Single-wire half-duplex communication

The single-wire half-duplex mode is selected by setting the HDSEL bit in the USART_CR3 
register. In this mode, the following bits must be kept cleared:

●

LINEN and CLKEN bits in the USART_CR2 register,

●

SCEN and IREN bits in the USART_CR3 register.

The USART can be configured to follow a single-wire half-duplex protocol. In single-wire 
half-duplex mode, the TX and RX pins are connected internally. The selection between half- 
and full-duplex communication is made with a control bit ‘HALF DUPLEX SEL’ (HDSEL in 
USART_CR3).

As soon as HDSEL is written to 1:

●

RX is no longer used,

●

TX is always released when no data is transmitted. Thus, it acts as a standard IO in idle 
or in reception. It means that the IO must be configured so that TX is configured as 
floating input (or output high open-drain) when not driven by the USART.

Idle or next

M=1 (9 data bits)

Clock (CPOL=0, CPHA=1)

Clock (CPOL=1, CPHA=0)

Clock (CPOL=1, CPHA=1)

Start LSB

MSB Stop

* LBCL bit controls last data clock pulse

Start

Idle or preceding

transmission

Data on TX

Stop

Clock (CPOL=0, CPHA=0)

0

1

2

3

4

5

6

7

*

*

*

*

8

transmission

Capture Strobe

LSB

MSB

Data on RX

0

1

2

3

4

5

6

7

(from slave)

(from master)

*

8

valid DATA bit

t

SETUP

t

HOLD

CK (capture strobe on CK
rising edge in this example)

Data on RX
(from slave)

t

SETUP 

= 

t

HOLD

 1/16 bit time

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments