manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 550 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 550

   

   

   

Secure digital input/output interface (SDIO)

RM0008

550/1096

 Doc ID 13902 Rev 12

Figure 215. Command path state machine (CPSM)

When the Wait state is entered, the command timer starts running. If the timeout is reached 
before the CPSM moves to the Receive state, the timeout flag is set and the Idle state is 
entered.

Note:

The command timeout has a fixed value of 64 SDIO_CK clock periods.

If the interrupt bit is set in the command register, the timer is disabled and the CPSM waits 
for an interrupt request from one of the cards. If a pending bit is set in the command register, 
the CPSM enters the Pend state, and waits for a CmdPend signal from the data path 
subunit. When CmdPend is detected, the CPSM moves to the Send state. This enables the 
data counter to trigger the stop command transmission.

Note:

The CPSM remains in the Idle state for at least eight SDIO_CK periods to meet the N

CC

 and 

N

RC

 timing constraints. N

CC

 is the minimum delay between two host commands, and N

RC

 is 

the minimum delay between the host command and the card response.

Idle

Pend

Send

Wait

Receive

Last Data

CPSM
disabled

Enabled and
command start

CPSM disabled or 
no response

Wait for response

Response
started

Response received or
disabled or command 
CRC failed

CPSM Disabled or
command timeout

CPSM Enabled and
pending command

ai14806b

Wait_CPL

Response Received in CE-ATA 
mode and no interrupt and
wait for CE-ATA Command
Completion signal enabled

Response Received in CE-ATA mode and
no interrupt and wait for CE-ATA
Command Completion signal disabled

CE-ATA Command 
Completion signal
received or
CPSM disabled or
Command CRC failed

On reset

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments