manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 842 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 842

   

   

   

USB on-the-go full-speed (OTG_FS)

RM0008

842/1096

 Doc ID 13902 Rev 12

Bit 14

ISOODRP:

 Isochronous OUT packet dropped interrupt

The core sets this bit when it fails to write an isochronous OUT packet into the RxFIFO 
because the RxFIFO does not have enough space to accommodate a maximum size packet 
for the isochronous OUT endpoint.

Note: Only accessible in device mode.

Bit 13

ENUMDNE:

 Enumeration done

The core sets this bit to indicate that speed enumeration is complete. The application must 
read the OTG_FS_DSTS register to obtain the enumerated speed.

Note: Only accessible in device mode.

Bit 12

USBRST:

 USB reset

The core sets this bit to indicate that a reset is detected on the USB.

Note: Only accessible in device mode.

Bit 11

USBSUSP:

 USB suspend

The core sets this bit to indicate that a suspend was detected on the USB. The core enters the 
Suspended state when there is no activity on the data lines for a period of 3 ms.

Note: Only accessible in device mode.

Bit 10

ESUSP:

 Early suspend

The core sets this bit to indicate that an Idle state has been detected on the USB for 3 ms.

Note: Only accessible in device mode.

Bits 9:8 Reserved

Bit 7

GONAKEFF:

 Global OUT NAK effective

Indicates that the Set global OUT NAK bit in the OTG_FS_DCTL register (SGONAK bit in 
OTG_FS_DCTL), set by the application, has taken effect in the core. This bit can be cleared by 
writing the Clear global OUT NAK bit in the OTG_FS_DCTL register (CGONAK bit in 
OTG_FS_DCTL).

Note: Only accessible in device mode.

Bit 6

GINAKEFF:

 Global IN non-periodic NAK effective

Indicates that the Set global non-periodic IN NAK bit in the OTG_FS_DCTL register (SGINAK 
bit in OTG_FS_DCTL), set by the application, has taken effect in the core. That is, the core has 
sampled the Global IN NAK bit set by the application. This bit can be cleared by clearing the 
Clear global non-periodic IN NAK bit in the OTG_FS_DCTL register (CGINAK bit in 
OTG_FS_DCTL).

This interrupt does not necessarily mean that a NAK handshake is sent out on the USB. The 
STALL bit takes precedence over the NAK bit.

Note: Only accessible in device mode.

Bit 5

NPTXFE:

 Non-periodic TxFIFO empty

This interrupt is asserted when the non-periodic TxFIFO is either half or completely empty, and 
there is space for at least one entry to be written to the non-periodic transmit request queue. 
The half or completely empty status is determined by the non-periodic TxFIFO empty level bit 
in the OTG_FS_GAHBCFG register (TXFELVL bit in OTG_FS_GAHBCFG).

Note: Accessible in host mode only.

Bit 4

RXFLVL:

 RxFIFO non-empty

Indicates that there is at least one packet pending to be read from the RxFIFO.

Note: Accessible in both host and device modes.

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments