manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 121 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 121

RM0008

Connectivity line devices: reset and clock control (RCC)

Doc ID 13902 Rev 12

121/1096

   

   

   

Low-power management reset

There are two ways to generate a low-power management reset:

1.

Reset generated when entering Standby mode: 

This type of reset is enabled by resetting nRST_STDBY bit in User Option Bytes. In this 
case, whenever a Standby mode entry sequence is successfully executed, the device 
is reset instead of entering Standby mode. 

2. 

Reset when entering Stop mode: 

This type of reset is enabled by resetting nRST_STOP bit in User Option Bytes. In this 
case, whenever a Stop mode entry sequence is successfully executed, the device is 
reset instead of entering Stop mode. 

For further information on the User Option Bytes, refer to the STM32F10xxx Flash 
programming manual. 

8.1.2 Power 

reset

A power reset is generated when one of the following events occurs: 

1.

Power-on/power-down reset (POR/PDR reset)

2. 

When exiting Standby mode

A power reset sets all registers to their reset values except the Backup domain (see 

Figure 4

)

These sources act on the NRST pin and it is always kept low during the delay phase. The 
RESET service routine vector is fixed at address 

0x0000_0004

 in the memory map. For more 

details, refer to 

Table 63: Vector table for other STM32F10xxx devices on page 195

.

The system reset signal provided to the device is output on the NRST pin. The pulse 
generator guarantees a minimum reset pulse duration of 20 µs for each reset source 
(external or internal reset). In case of an external reset, the reset pulse is generated while 
the NRST pin is asserted low.

Figure 10.

Simplified diagram of the reset circuit

.234

2

05

6

$$

6

$$!

77$'RESET
)7$'RESET

0ULSE

GENERATOR

0OWERRESET

%XTERNAL

RESET

MIN—S 

3YSTEMRESET

&ILTER

3OFTWARERESET
,OWPOWERMANAGEMENTRESET

AIB

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments