manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 169 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 169

RM0008

General-purpose and alternate-function I/Os (GPIOs and AFIOs)

Doc ID 13902 Rev 12

169/1096

   

   

   

9.3 

Alternate function I/O and debug configuration (AFIO)

To optimize the number of peripherals available for the 64-pin or the 100-pin or the 144-pin 
package, it is possible to remap some alternate functions to some other pins. This is 
achieved by software, by programming the 

AF remap and debug I/O configuration register 

(AFIO_MAPR) on page 178

. In this case, the alternate functions are no longer mapped to 

their original assignations. 

9.3.1 Using 

OSC32_IN/OSC32_OUT 

pins as GPIO ports PC14/PC15

The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general-purpose I/O 
PC14 and PC15, respectively, when the LSE oscillator is off. The LSE has priority over the 
GP IOs function.

Note:

1

The PC14/PC15 GPIO functionality is lost when the 1.8 V domain is powered off (by 
entering standby mode) or when the backup domain is supplied by V

BAT

 (V

DD

 no more 

supplied). In this case the IOs are set in analog mode.

2

Refer to the note on IO usage restrictions in 

Section 5.1.2 on page 67

.

9.3.2 Using 

OSC_IN/OSC_OUT pins as GPIO ports PD0/PD1

The HSE oscillator pins OSC_IN/OSC_OUT can be used as general-purpose I/O PD0/PD1 
by programming the PD01_REMAP bit in the 

AF remap and debug I/O configuration register 

(AFIO_MAPR)

.

This remap is available only on 36-, 48- and 64-pin packages (PD0 and PD1 are available 
on 100-pin and 144-pin packages, no need for remapping).

Note:

The external interrupt/event function is not remapped. PD0 and PD1 cannot be used for 
external interrupt/event generation on 36-, 48- and 64-pin packages.

Bit 16

LCKK[16]:

 Lock key

This bit can be read anytime. It can only be modified using the Lock Key Writing Sequence. 
0: Port configuration lock key not active
1: Port configuration lock key active. GPIOx_LCKR register is locked until an MCU reset 
occurs.

LOCK key writing sequence:

Write 1
Write 0
Write 1
Read 0
Read 1 (this read is optional but confirms that the lock is active)

Note: During the LOCK Key Writing sequence, the value of LCK[15:0] must not change.

Any error in the lock sequence will abort the lock.

Bits 15:0

LCKy:

 Port x Lock bit y (y= 0 .. 15)

These bits are read write but can only be written when the LCKK bit is 0. 
0: Port configuration not locked 
1: Port configuration locked.

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments