manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 879 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 879

RM0008

USB on-the-go full-speed (OTG_FS)

Doc ID 13902 Rev 12

879/1096

   

   

   

OTG_FS device endpoint-x interrupt register (OTG_FS_DIEPINTx) (x = 0..3, 
where x = Endpoint_number)

Address offset: 0x908 + (Endpoint_number × 0x20)

Reset value: 0x0000 0080

This register indicates the status of an endpoint with respect to USB- and AHB-related 
events. It is shown in 

Figure 309

. The application must read this register when the IN 

endpoints interrupt bit of the Core interrupt register (IEPINT in OTG_FS_GINTSTS) is set. 
Before the application can read this register, it must first read the device all endpoints 
interrupt (OTG_FS_DAINT) register to get the exact endpoint number for the Device 
endpoint-x interrupt register. The application must clear the appropriate bit in this register to 
clear the corresponding bits in the OTG_FS_DAINT and OTG_FS_GINTSTS registers.

         

         

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Reserved

TXFE

INEP

NE

Reser

v

ed

ITTXFE

TO

C

Reser

v

ed

EPDI

S

D

XF

R

C

r

rc_

w1
/rw

rc_

w1

rc_

w1

rc_

w1

rc_

w1

Bits 31:8 Reserved

Bit 7

TXFE:

 Transmit FIFO empty

This interrupt is asserted when the TxFIFO for this endpoint is either half or completely empty. 
The half or completely empty status is determined by the TxFIFO Empty Level bit in the 
OTG_FS_GAHBCFG register (TXFELVL bit in OTG_FS_GAHBCFG).

Bit 6

INEPNE:

 IN endpoint NAK effective

This bit can be cleared when the application clears the IN endpoint NAK by writing to the 
CNAK bit in OTG_FS_DIEPCTLx.

This interrupt indicates that the core has sampled the NAK bit set (either by the application or 
by the core). The interrupt indicates that the IN endpoint NAK bit set by the application has 
taken effect in the core.

This interrupt does not guarantee that a NAK handshake is sent on the USB. A STALL bit 
takes priority over a NAK bit.

Bit 5 Reserved

Bit 4

ITTXFE:

 IN token received when TxFIFO is empty

Applies to non-periodic IN endpoints only.

Indicates that an IN token was received when the associated TxFIFO (periodic/non-periodic) 
was empty. This interrupt is asserted on the endpoint for which the IN token was received.

Bit 3

TOC:

 Timeout condition

Applies only to Control IN endpoints.

Indicates that the core has detected a timeout condition on the USB for the last IN token on 
this endpoint. 

Bit 2 Reserved.

Bit 1

EPDISD:

 Endpoint disabled interrupt

This bit indicates that the endpoint is disabled per the application’s request.

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments