manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 1036 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 1036

   

   

   

Ethernet (ETH): media access control (MAC) with DMA controller

RM0008

1036/1096

 Doc ID 13902 Rev 12

Bit 21

TSF:

 Transmit store and forward

When this bit is set, transmission starts when a full frame resides in the Transmit FIFO. When 
this bit is set, the TTC values specified by the ETH_DMAOMR register bits [16:14] are ignored.

When this bit is cleared, the TTC values specified by the ETH_DMAOMR register bits [16:14] 
are taken into account.

This bit should be changed only when transmission is stopped.

Bit 20

FTF:

 Flush transmit FIFO

When this bit is set, the transmit FIFO controller logic is reset to its default values and thus all 
data in the Tx FIFO are lost/flushed. This bit is cleared internally when the flushing operation is 
complete. The Operation mode register should not be written to until this bit is cleared.

Bits 19:17 Reserved

Bits 16:14

TTC:

 Transmit threshold control

These three bits control the threshold level of the Transmit FIFO. Transmission starts when the 
frame size within the Transmit FIFO is larger than the threshold. In addition, full frames with a 
length less than the threshold are also transmitted. These bits are used only when the TSF bit 
(Bit 21) is cleared.

000: 64
001: 128
010: 192
011: 256
100: 40
101: 32
110: 24
111: 16

Bit 13

ST:

 Start/stop transmission 

When this bit is set, transmission is placed in the Running state, and the DMA checks the 
transmit list at the current position for a frame to be transmitted. Descriptor acquisition is 
attempted either from the current position in the list, which is the transmit list base address set 
by the ETH_DMATDLAR register, or from the position retained when transmission was 
stopped previously. If the current descriptor is not owned by the DMA, transmission enters the 
Suspended state and the transmit buffer unavailable bit (ETH_DMASR [2]) is set. The Start 
Transmission command is effective only when transmission is stopped. If the command is 
issued before setting the DMA ETH_DMATDLAR register, the DMA behavior is unpredictable.

When this bit is cleared, the transmission process is placed in the Stopped state after 
completing the transmission of the current frame. The next descriptor position in the transmit 
list is saved, and becomes the current position when transmission is restarted. The Stop 
Transmission command is effective only when the transmission of the current frame is 
complete or when the transmission is in the Suspended state.

Bits 12:8 Reserved

Bit 7

FEF:

 Forward error frames

When this bit is set, all frames except runt error frames are forwarded to the DMA.

When this bit is cleared, the Rx FIFO drops frames with error status (CRC error, collision error, 
giant frame, watchdog timeout, overflow). However, if the frame’s start byte (write) pointer is 
already transferred to the read controller side (in Threshold mode), then the frames are not 
dropped. The Rx FIFO drops the error frames if that frame's start byte is not transferred 
(output) on the ARI bus.

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments