Sony PetaSite DMS-B110S Installation Manual Download Page 99

Page: 99 / 112

6-73

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

6-11-7. Installation of the DMSA-SBE1

Set the POWER switch of the DMSA-SBE1 to the I
(ON) position.

Fix the two monitor fixing plates with the four screws
(PWH4

8).

Fix the DMSA-SBE1 by the belt supplied with the
monitor fixing plate as shown in the following illustra-
tion.

POWER switch

DMSA-SBE1

When drives are installed in the two slots
of upper and lower slots of the console.

When drives are installed in the lower slot
only of the console.

Monitor fixing plate

Belt

Monitor fixing plate

Belt

DMS-B150L/B210S

DMS-EX150L/EX210S

DMS-B80L/B110S

PWH4

PWH
4

6-11. Installing the Package Supporting Equipment

Summary of Contents for PetaSite DMS-B110S

















































































































Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands

Sony PetaSite DMS-B110S, Installation Manual

Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands