manualshive.com logo in svg

Sony PetaSite DMS-B110S, Installation Manual, Page: 92 / 112

Share
Download
Sony PetaSite DMS-B110S Installation Manual Download Page 92

6-66

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

2. When four to six units of the extension

consoles are installed.

(1) Connect the harness (DMS-B150L side) of the already

wired AC outlet to the terminal (AC OUT2) of the AC
unit (30A) assembly of the fourth console.

(2) Connect the harness of the already wired AC outlet of

the fourth extension console through the bottom hole
of the frame to the AC outlet of the fifth extension
console.

(3) Connect the AC power in the same way as step (2) for

the fifth and sixth extension consoles.

Harness of the already wired AC outlet

Fourth extension
console

AC unit (30A) assembly

Screws
(P3 

x

 6) 

Harness (GRN)

Harness (WHT)

Harness (BLK)

Terminal table screws
(M4 

x

 8)

Fourth extension
console

Fifth extension
console

GRN

WHT

BLK

AC outlet (6-pin)

AC outlet (6-pin)

6-11. Installing the Package Supporting Equipment

Summary of Contents for PetaSite DMS-B110S

















































































































Reviews:

No comments