Sony PetaSite DMS-B110S Installation Manual Download Page 29

Page: 29 / 112

6-3

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

2. Table top

Removal

Open the drive stage panel. (Refer to “1. Drive stage
panel”.)

Remove the six screws.

Remove the table top.

Installation

Reattach the table top in reverse order of disassembling.

6-2. Removal and Installation of the Cabinets

PWH4

Table top

3. Stage panel support

Removal

Remove the drive stage panel. (Refer to “1. Drive
stage panel”.)

Remove the four screws.

Remove the stage panel supports (U).

Remove the six screws (PWH4

12).

Remove the two hexagonal head cap bolts (M4

8).

Remove the stage panel support assembly.

Be careful not to drop the

6 poly washer. If it is

dropped, insert it into the pin as shown in the figure.

Installation

Reattach the stage panel supports in reverse order of
disassembling.

PSW4

Stage panel support (U)

poly washer

PWH4

Stage panel support
assemblies

Summary of Contents for PetaSite DMS-B110S

















































































































Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands

Sony PetaSite DMS-B110S, Installation Manual

Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands