Sony PetaSite DMS-B110S Installation Manual Download Page 70

Page: 70 / 112

6-44

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

(2) Loosen the two fixing screws of the drive drive stage

and pull out the drive stage until the lock levers of the
right and left rails are locked.

(3) Align the legs on the front panel side of the tape drive

with the positioning holes on the back of the drive
stage.

Fixing screws

Drive stage

Lock lever

Handle

(4) Slide the tape drive to the back of the drive stage.

Install the tape drive until the legs on the rear panel
side are aligned with the positioning holes on the front
of the drive stage.

(5) While pushing the lock levers on the right and left rails

of the drive stage, push in the drive stage.

(6) Tighten the two fixing screws of the drive stage.
(7) Close the drive stage panel of the basic console and fix

it with the four screws (with drop-safe).

Positioning holes

Tape drive

Drive stage

Lock lever

Drive stage

Lock lever

6-9. Installation of the Tape Drive

Positioning holes

Tape drive

Front panel

Drive stage

Summary of Contents for PetaSite DMS-B110S

















































































































Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands

Sony PetaSite DMS-B110S, Installation Manual

Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands