Sony PetaSite DMS-B110S Installation Manual Download Page 31

Page: 31 / 112

6-5

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

5. Front top plate, front base plate, side panels

(FL/FR)

Removal

Remove the drive stage panel. (Refer to “1. Drive
stage panel”.)

Remove the table top. (Refer to “2. Table top”.)

Remove the stage panel support. (Refer to “3. Stage
panel support”.)

Remove the drive stage. (Refer to “4. Drive stage”.)

Loosen the four hexagonal head cap bolts and remove
the two hexagonal head cap bolts on front top plate.

Remove front top plate in the direction of the arrow.

Front top plate

mark : Loosen the bolt
(hexagonal head cap bolt M4

mark : Remove the bolt (M4

(hexagonal head cap bolt M4

Loosen the two hexagonal head cap bolts and remove
the two screws on side panel (FL).

Remove the side panel (FL) in the direction of the arrow.

Loosen the two hexagonal head cap bolts and remove
the two hexagonal head cap bolts on side panel (FR).

10. Remove the side panel (FR) in the direction of the arrow.

11. Loosen the three hexagonal head cap bolts and remove

the two hexagonal head cap bolts on front base plate.

12. Remove the front base plate.

Installation

Fix all of the parts tentatively first, then tighten the bolts in
reverse order of disassembling.

Side panel (FL)

Side panel (FR)

mark : Loosen the bolt (hexagonal head cap bolt M4

mark : Remove the bolt (hexagonal head cap bolt M4

Front base plate

mark : Loosen the bolt
(hexagonal head cap bolt M4

mark : Remove the bolt
(hexagonal head cap bolt M4

6-2. Removal and Installation of the Cabinets

Summary of Contents for PetaSite DMS-B110S

















































































































Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands

Sony PetaSite DMS-B110S, Installation Manual

Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands